by Mark Anderson
This is Part II in a two-part series. Check out Part I, especially the many warnings and disclaimers, here.
While the “standard method” of Iontophoresis was working well for me, I found it annoying to submerge both hands simultaneously, when only one hand was getting treated. Furthermore, it seems unnecessarily risky to run current across both arms and shoulders, potentially through several vital organs, if it can be avoided. So, always looking to optimize things, I’ve been experimenting with what I call the “1-tin method”. This involves using a dampened wristband, placed somewhere along the forearm of the submerged hand, to close the circuit (instead of a second tin-full of water). With this setup, the current only runs through one hand and forearm (at a time), and the other hand is free to do…whatever it is you do with a free hand when nobody is watching*.
[*I’m assuming you will do this when no one is watching. Seriously, you’d have to be nuts to do this in front of other people. They’ll have you hauled off to the loony bin right quick.]
The following hardware is needed for the 1-Tin Method:
-1 metal tin
-2-4 Electrical wires with “alligator clips” on each end
-2-3 6v lantern batteries
-A pinch or two of salt
-1 Wrist sweatband
-(Optional) Non-conductive spacer, such as a plastic tupperware lid
-(OptionalP) Piece of aluminum foil, approximately 12” x 18”
Wire everything up as shown in the photo. If using multiple batteries in series, wire them together as for the Standard Method (with the negative terminal of the 1st battery connected to the positive terminal of the 2nd, the negative terminal of the 2nd battery connected to the positive terminal of the 3rd, and so on). Clip the negative terminal of the last battery to the metal tin, and the positive terminal of the first battery to the dampened wrist-band (more on this below). I like to clip the wire to the outside of the wrist-band to ensure the metal clip doesn’t directly contact my skin. Use the same timing and frequency as for the Standard Method, but without reversing the polarity half-way through (so each hand gets submerged one time).
The 1-tin method is not yet perfected, and has at least one downside. That is a burning pain in the vicinity of the alligator clip on the sweatband. This is because the dampened sweatband doesn’t diffuse the electricity as well as a tin full of water. One way to mitigate this is to move the alligator clip around whenever the pain becomes excessive (typically twice during a 10-minute session, but it depends on pain tolerance, voltage and water chemistry). A better option is to wrap foil around the wristband, which seems to 1) GREATLY increase conductivity, meaning less voltage is required, and 2) better diffuse the current, so it’s slightly less painful in the area of the alligator clip. To do this, fold up a piece of aluminum foil into a long, wristband-width strip, and wrap this around the damp wristband (see pic below). Roll the two ends of the foil together until the wrap is just tight enough to stay in place (note, the tighter it is, the better current will flow–this may be good or bad depending on the voltage you are using). Clip the wire to the seam in the foil. If you do this with 24v, you will get quite a significant shock! The most I’ve used is 18v, and even that is much more intense than 24v without foil.
The other complication of the 1-Tin Method is that polarity of the circuit (probably) becomes much more important. With two tins, the polarity is reversed half-way through, so both hands will be subjected to current flowing in both directions. That is not the case with one tin. While the mechanism of iontophoresis is unknown, it is likely that current polarity is important, because it determines the direction of flow of positively and negatively charged ions (positively charged ions, such as sodium ions, move away from the positively charged battery pole; negatively charged ions, such as chlorine ions, move toward the positively charged pole—both of these ions are produced when salt is dissolved in water, and sodium ions are a primary component of sweat).
The importance of ion flow is well-understood for the delivery of medications via iontophoresis, and each medicine’s ionic polarity (when dissolved in water) is clearly identified**. For hand drying applications, determining which is “right” through logic is difficult, since nobody seems to know what exactly causes the drying effect. Do we want to push positive ions into the hand? Do we want to pull negative ions out? Does it matter which ions are at play? I don’t know. So I’ve experimented and come up with my best guess: if using salt in the water, the batteries should be wired such that the negative pole of the last battery attaches to the metal tin, and the positive pole of the first battery attaches to the dampened wrist band. If you think I’m wrong, please tell me!
[**Here’s a good source that describes the science behind iontophoresis for medicine delivery. Incidentally, it states “Positive ions accumulating at the negative pole…produce hardening of the tissues by increasing protein density,” further suggesting that the negative battery pole should be wired to the pan.]
Tips on the 1-Tin Method:
- Do this at your own risk
- Talk to your doctor before electrocuting yourself
- Please don’t do this if you are pregnant, have a pacemaker, or any other metal implants in the path of the current flow.
- Definitely don’t do this if you have a heart condition, epilepsy, or other medical condition that responds poorly to electricity.
- Probably, just don’t do this.
- I find that I need less voltage for the 1-Tin Method than I do for the Standard Method to get the same effect (for example 18v vs. 24v). Start with low voltage and ramp up if necessary. Adding foil further reduces the required voltage.
- The wrist band will dry out during the session, thus reducing conductivity, so it helps to have a sponge handy that you can use to re-moisten the wrist-band every few minutes. Note, this doesn’t seem to be a problem if you use foil around the wristband.
- Water may trickle down your arm, from the wrist-band, toward the pan. It helps to have a small towel handy to dry the trickle of water (in order to avoid shorting the circuit).
- You may notice skin redness in the vicinity of the water line of the metal tin(s) and/or where the wristband was located. This is “normal” (within the context of submerging your body in electrically charged buckets of water), and seems to fade within a couple hours.
I’ve been using the 1-tin method exclusively for the last month, but I’m still not sold on it. On the plus side, it’s really nice to have a free hand, and I’d like to think I’m reducing some risk by limiting the current flow to my forearm. But I’m not sure it works as well, and I’m still not certain I have the polarity correct. I think we need a few more people trying it a few different ways to reach a more definitive conclusion. I plan to keep experimenting until I find the system that works best for me.
For more information on iontophoresis for climbers, and to ask questions from experienced climber-iontophoresis-users, check out this thread on our forum.